Sikaflex 11fc | 600ml White Sausage

Your price:

RRP: $20.84
Save $1.54

Immediate Despatch
Immediate Despatch
We currently hold stock of this item in our warehouse. Purchase this item before 11am and it will be shipped today
Parcel type: Small item
Parcel type: Small item
Small package item can be added to the cart for express checkout.


Full Details

Sikaflex  11FC - One component polyurethane sealant/adhesive 

Uses As an elastic adhesive for: 

  • Assembling metal framed buildings. 
  • Cover plates and covings. 
  • Light-weight construction materials. 
  • Acoustic ceiling tiles. 
  • Wood, metal or plastic window and door frames. 
  • Floor mouldings and door sills. 
  • As an elastic joint sealant for: 
  • Sealing joints in concrete, epoxy, stone and quarry tiled floors. 
  • Sealing joints in roofing and guttering etc. 
  • Flexible draught proofing. 
  • Containers, water tanks and silos. 
  • Excellent pick resistance for applicati ons in shop fronts, prisons, schools, public amenities and buildings. 
  • Bolted lap joints. 
  • Sealing penetrations in walls or floors for ducts, piping, etc. 
  • Sanitary purposes. 


  • New Sikaflex 11FC will bond to well cleaned old Sikaflex 11FC. 
  • Excellent adhesion on all cement-based  materials, brick, ceramics, metals, wood, polyurethane, epoxy, and some polyesters.
  • Fast cure rate. 
  • High durability. 
  • High abrasion resistanc e and tear strength. 
  • Good weathering and water resistance. 
  • Non-sag on vertical joints up to 30 mm width. 
  • Ready for immediate use – no mixing.
  • Non-corrosive.
  • Can be painted over with many water, solvent and rubber-based paints (preliminary tests recommended). 
  • Certified for use in contact with potable water (AS4020-2005). 

Instructions for Use: Surface Preparation: Clean, sound, dry and free of oil, grease and surface contaminants such as form release agents, curing membrances and hydrophobic water repellents. Throughly remove all loose particles and dust.


  • Minimum application temperature 5°C.
  • For easier use store cartridge at temperature between 10°C and 20°C.
  • Break inner seal at extrusion end of cartridge.
  • Affix nozzle to cartridge, cut tip to suit joint size.
  • Install into a caulking gun
  • For adhesive purpose apply in spots or beads on the prepared surface, tapping or pressing the part to be adhered against the substrate.
  • The thickness of the bead depends on the surface texture (1mm to 5mm). When sealing is completed, joints may be smoothed with a 20% solution of washing up detergent in water. When masking sides of joints for neatness, remove tape before the sealent cures.
  • Always allow sufficient surface exposed to moisture.

Technical Data (Typical) 

 Colours Grey, White, Black, Beige
 Density 1.15 – 1.2 kg/litre depending on colour
 Basis    Accelerated moisture curing polyurethane prepolymer
 Priming Refer separate Primer Selection Guide for details
 Application Temperature 5°C to 40°C   
 Service Temperature  -40°C to 80°C (maximum 50°C in water) 
 Shelf Life  Minimum 12 months stored dry below 30°C unopened in original container 
 Skinning Time  45 to 75 minutes depending on climate 
 Shore A hardness 40-45
 Elastic Recovery >90% 
 Tensile Strength  0.5 MPa approx. @ 50% elongation (20°C) 
 Elongation at Break  Over 450% 
 Maximum Working Expansion and  Contraction Refer Joint Design section
 Tear propagation resistance 7 MPa   
 Tensile Strength at Break  Approx. 1.4 MPa 



Chemical Resistance 


 Long Term Medium Term Low to Very Low Term  
Weak acids 
Weal alkalis 
Mineral oils 
Vegetable oils 
Organic solvents 
Paint thinners 
Strong acids 
Strong alkalis




One pack of Sikaflex-11FC will produce the following lengths of bead for various bead diameters (approx. per pack):  



 310 ml Cartridge  600 ml Sausage  
3 mm bead 
4 mm bead 
5 mm bead 
6 mm bead 
43 metres 
24 metres 
15 metres 
10 metres  
3 mm bead 
4 mm bead 
5 mm bead 
6 mm bead   
81 metres 
45 metres 
28 metres 
19 metres